Customer Service M-F 8am-7pm
1-888-695-7994
One of our sales reps is standing by to help with any questions you may have about the parts we sell.

Fuses

A fuse consists of either a wire fuse element or a metal strip inside a small cross-section which are connected to circuit conductors. These devices are usually mounted between two electrical terminals and normally the fuse is cased in a non-conducting and non-combustible housing. The fuse is arranged in series which could carry all the current passing throughout the protected circuit. The resistance of the element produces heat due to the current flow. The size and the construction of the element is empirically determined to be certain that the heat produced for a normal current does not cause the element to reach a high temperature. In instances where too high of a current flows, the element either melts directly or it rises to a higher temperature and melts a soldered joint within the fuse which opens the circuit.

If the metal conductor parts, an electric arc is formed between un-melted ends of the fuse. The arc begins to grow until the required voltage so as to sustain the arc is in fact greater than the circuits accessible voltage. This is what leads to the current flow to become terminated. Where alternating current circuits are concerned, the current naturally reverses course on each and every cycle. This particular process really improves the fuse interruption speed. Where current-limiting fuses are concerned, the voltage needed in order to sustain the arc builds up fast enough to essentially stop the fault current previous to the first peak of the AC waveform. This effect greatly limits damage to downstream protected units.

The fuse is often made out of silver, aluminum, zinc, copper or alloys in view of the fact that these allow for predictable and stable characteristics. The fuse ideally, will carry its current for an indefinite period and melt rapidly on a small excess. It is vital that the element should not become damaged by minor harmless surges of current, and must not change or oxidize its behavior after possible years of service.

The fuse elements may be shaped in order to increase the heating effect. In bigger fuses, the current could be divided among several metal strips, while a dual-element fuse might have metal strips which melt at once upon a short-circuit. This particular type of fuse may likewise comprise a low-melting solder joint which responds to long-term overload of low values as opposed to a short circuit. Fuse elements could be supported by steel or nichrome wires. This would make sure that no strain is placed on the element but a spring may be integrated so as to increase the speed of parting the element fragments.

The fuse element is commonly surrounded by materials which perform to speed up the quenching of the arc. Some examples comprise silica sand, air and non-conducting liquids.

Click to Download the pdf



Forklift Masts and Parts

  • Alternators
    A device used to transform mechanical energy into electrical energy is actually called an alternator. It can perform this function in the form of an electric current. An AC electrical generator could basically also be termed an alternator. Then ...
    More
  • Brakes
    A brake drum is wherein the friction is supplied by the brake shoes or brake pads. The shoes or pads press up against the rotating brake drum. There are some different brake drums kinds along with certain specific differences. A "break drum" ...
    More
  • Carriage Rollers
    Carriage rollers are particularly designed bearings that are utilized on lift masts in order to help them function within tough environmental surroundings. Lift masts are often subjected to oscillations, shocks, high dynamic and vibrations and ...
    More
  • Carriages and Carriage Parts
    There are 4 sizings of hook type tine carriages rated by the fork carriage lifting capability. Hook type tine carriages have been standardized. The carriage bar spacing used for Class 1 is something like thirteen inches and the Class 1 ...
    More
  • Control Valves
    Automatic control systems were first developed more than two thousand years ago. The ancient water clock of Ktesibios in Alexandria Egypt dating to the 3rd century B.C. is believed to be the first feedback control equipment on record. This ...
    More
  • Controllers
    Lift trucks are obtainable in several various models that have different load capacities. Most standard forklifts used inside warehouse settings have load capacities of 1-5 tons. Larger scale units are used for heavier loads, like loading ...
    More
  • Differentials
    A mechanical tool which can transmit torque and rotation through three shafts is known as a differential. Every now and then but not all the time the differential would utilize gears and will function in two ways: in cars, it receives one input ...
    More
  • Drive Axles
    A forklift drive axle is a piece of machinery which is elastically affixed to a vehicle frame utilizing a lift mast. The lift mast is fixed to the drive axle and can be inclined round the axial centerline of the drive axle. This is done by at the ...
    More

Lift Parts Express

We are here to provide you with the best service and sales support for all your lift truck parts needs. Our devotion to excellence is what sets us apart from our competition. For more information give us a call today at:

TOLL FREE: 1-888-695-7994


www.forkliftmastscalifornia.com

Email Us



Our business objective is to ensure every customer we serve is content with the parts or attachments they are given. One of our major competitive advantages is that we can generally match or beat...   About Us