Customer Service M-F 8am-7pm
1-888-695-7994
One of our sales reps is standing by to help with any questions you may have about the parts we sell.

Forklift Starters

The starter motor nowadays is normally either a series-parallel wound direct current electric motor which has a starter solenoid, which is similar to a relay mounted on it, or it can be a permanent-magnet composition. When current from the starting battery is applied to the solenoid, mainly via a key-operated switch, the solenoid engages a lever which pushes out the drive pinion that is positioned on the driveshaft and meshes the pinion utilizing the starter ring gear that is seen on the engine flywheel.

The solenoid closes the high-current contacts for the starter motor, that starts to turn. Once the engine starts, the key operated switch is opened and a spring within the solenoid assembly pulls the pinion gear away from the ring gear. This particular action causes the starter motor to stop. The starter's pinion is clutched to its driveshaft by an overrunning clutch. This permits the pinion to transmit drive in just one direction. Drive is transmitted in this way via the pinion to the flywheel ring gear. The pinion remains engaged, like for example for the reason that the driver fails to release the key as soon as the engine starts or if there is a short and the solenoid remains engaged. This causes the pinion to spin separately of its driveshaft.

The actions discussed above would stop the engine from driving the starter. This important step stops the starter from spinning really fast that it could fly apart. Unless adjustments were made, the sprag clutch arrangement would stop making use of the starter as a generator if it was employed in the hybrid scheme mentioned prior. Usually an average starter motor is intended for intermittent utilization that will stop it being used as a generator.

Hence, the electrical parts are intended to be able to function for around under thirty seconds to be able to prevent overheating. The overheating results from too slow dissipation of heat because of ohmic losses. The electrical components are intended to save cost and weight. This is the reason nearly all owner's guidebooks meant for automobiles recommend the operator to pause for at least 10 seconds right after each and every ten or fifteen seconds of cranking the engine, when trying to start an engine which does not turn over right away.

The overrunning-clutch pinion was launched onto the marked in the early part of the 1960's. Previous to the 1960's, a Bendix drive was utilized. This drive system operates on a helically cut driveshaft that has a starter drive pinion placed on it. As soon as the starter motor begins spinning, the inertia of the drive pinion assembly allows it to ride forward on the helix, hence engaging with the ring gear. When the engine starts, the backdrive caused from the ring gear allows the pinion to surpass the rotating speed of the starter. At this moment, the drive pinion is forced back down the helical shaft and therefore out of mesh with the ring gear.

The development of Bendix drive was made in the 1930's with the overrunning-clutch design called the Bendix Folo-Thru drive, developed and introduced in the 1960s. The Folo-Thru drive has a latching mechanism together with a set of flyweights within the body of the drive unit. This was an improvement since the average Bendix drive utilized to be able to disengage from the ring once the engine fired, though it did not stay functioning.

As soon as the starter motor is engaged and begins turning, the drive unit is forced forward on the helical shaft by inertia. It then becomes latched into the engaged position. As soon as the drive unit is spun at a speed higher than what is attained by the starter motor itself, for instance it is backdriven by the running engine, and next the flyweights pull outward in a radial manner. This releases the latch and allows the overdriven drive unit to become spun out of engagement, therefore unwanted starter disengagement can be prevented previous to a successful engine start.

Click to Download the pdf



Forklift Masts and Parts

  • Alternators
    A device used to transform mechanical energy into electrical energy is actually called an alternator. It can perform this function in the form of an electric current. An AC electrical generator could basically also be termed an alternator. Then ...
    More
  • Brakes
    A brake drum is wherein the friction is supplied by the brake shoes or brake pads. The shoes or pads press up against the rotating brake drum. There are some different brake drums kinds along with certain specific differences. A "break drum" ...
    More
  • Carriage Rollers
    Carriage rollers are particularly designed bearings that are utilized on lift masts in order to help them function within tough environmental surroundings. Lift masts are often subjected to oscillations, shocks, high dynamic and vibrations and ...
    More
  • Carriages and Carriage Parts
    There are 4 sizings of hook type tine carriages rated by the fork carriage lifting capability. Hook type tine carriages have been standardized. The carriage bar spacing used for Class 1 is something like thirteen inches and the Class 1 ...
    More
  • Control Valves
    Automatic control systems were first developed more than two thousand years ago. The ancient water clock of Ktesibios in Alexandria Egypt dating to the 3rd century B.C. is believed to be the first feedback control equipment on record. This ...
    More
  • Controllers
    Lift trucks are obtainable in several various models that have different load capacities. Most standard forklifts used inside warehouse settings have load capacities of 1-5 tons. Larger scale units are used for heavier loads, like loading ...
    More
  • Differentials
    A mechanical tool which can transmit torque and rotation through three shafts is known as a differential. Every now and then but not all the time the differential would utilize gears and will function in two ways: in cars, it receives one input ...
    More
  • Drive Axles
    A forklift drive axle is a piece of machinery which is elastically affixed to a vehicle frame utilizing a lift mast. The lift mast is fixed to the drive axle and can be inclined round the axial centerline of the drive axle. This is done by at the ...
    More

Lift Parts Express

We are here to provide you with the best service and sales support for all your lift truck parts needs. Our devotion to excellence is what sets us apart from our competition. For more information give us a call today at:

TOLL FREE: 1-888-695-7994


www.forkliftmastscalifornia.com

Email Us



Our business objective is to ensure every customer we serve is content with the parts or attachments they are given. One of our major competitive advantages is that we can generally match or beat...   About Us